Battery for 12V Auto Capsule

12V powerbank

Refrence : 21246

Multipurpose battery for Handpresso Auto Capsule 12V

Out of stock
€89.00

Interested in this product? Drop us an email and we will let you know when it's available for order.

A must have for your 12V coffee machine to follow you wherever you go!

8000mA battery to use your Handpresso Auto Capsule espresso machine anywhere.

Allows you to make 5 espressos with one charge.

Only for Handpresso Auto Capsule - Does not work for Handcoffee Auto.

This battery also allows you to recharge your phone and serves as jumper cables for your car. It is also equipped with ultra-bright LEDs for emergency lighting.

Charging time with fast USB charger : 2h

Charging time with standard USB charger : 6h

Battery weight: 375g

Contents:

- 1 Baseus 8000mA powerbank

- 1 pair of Smart Jumper cables

- 1 micro USB cable

- 1 12V cable

- User manual

CAUTION in case of use on a car:

1. Please read the instructions carefully and follow the instructions carefully before using the starter. Any improper operation can damage the starter or prevent the car from starting.

2. Do not start any engine whose displacement exceeds the maximum displacement that the unit can withstand, otherwise it will be damaged.

3. Your jump starter will perform best when its battery is fully charged. If loaded below 50%, it may not be able to start your engine. Please charge your power bank periodically (at least once, with 5 months recommended).

4. Do not connect positive and negative polarities when the system is powered on. Allow the jump starter to cool for at least 30 seconds after each start.

5. Never leave the device connected to the vehicle battery after successfully starting your car. Once the engine has started successfully, immediately disconnect the heavy duty cable clamps.

6. Do not use the product in high temperature or place it in the high temperature environment for a long time.

CAUTION when using on a car:

1. Please read the instructions carefully and follow the instructions carefully before using the starter. Incorrect operation may damage the starter or prevent the car from starting.

2. Do not start engines that exceed the maximum displacement the unit can handle, as this will damage the unit.

3. Your jump starter will work best when its battery is fully charged. If charged less than 50%, it may not be able to start your engine. Please charge your power bank periodically (at least once evry 5 months recommended).

4. Do not connect the positive and negative polarities when the system is powered. Allow the jump starter to cool for at least 30 seconds after each start.

5. Never leave the device connected to the vehicle battery after your car has been successfully started. Once the engine has successfully started, immediately disconnect the heavy-duty cable ties.

6. Do not use the product in high temperature and do not place it in high temperature environment for a long time.

  • Size
    16 x 3 x 8,5 cm
  • Voltage
    12 V DC
  • Power
    120 Watt
  • Compatible with
    Handpresso Auto Capsule

How to use the BASEUS Jump Starter? Using the device as a 12V jump starter:

 1.Insert the smart ignition clip into the EC5 interface of the startuppower supply, the red light and green light of the smart clip will flash alternately

 2.Clamp the positive and negative anodes of the smart ignition clip on to the car battery respectively. The red clip should be connected to the positive (+) end, while the black clip should be connected to the negative (-) end.

Then, follow the instructions below:

 When the green light is turned on, the connection is correct and the battery can be jump started.

When the red light is turned on, the clips are connected to the wrong ends. Connect the clips correctly and make sure the green light is turned on before jump starting the battery.

 3.Go back to the car and start the car

 4.Remove the start-up power immediately after starting the car

 

(Notes: When the ignition clip is connected to the battery in order, if the indicator light on the side of the ignition clip lights up red, you need to use the forced start switch---------Disconnect the negative pole of the ignition clip and press and hold the forced start switch on the side of the ignition clip for 3-5 seconds When the ignition clip indicator lights green, connect the negative pole to the battery.Then start the car.)